Search results

Excellent condition, near new except for the shop worn paint from being under my workbench for decades . Not sure of the manufacturer, I bought it from Enco in 1979 but all the fasteners are Imperial, not metric, the T slots are 5/8". Includes angle mount and tailstock, both never used. Almost...

Complete setup including 50+ lbs of powder, use to build up shafts and etc and apply coatings. $2000. The O/A hoses are stiff and need replaced, the rest is ready to go. Full documentation included. I bought it new and kept everything.

8" wide jaws, opens to 14.5". Weighs approx 300 lbs. 8 tons clamping force. No hard jaws. $650 Located in PA 17602

Toolmex brand. Good used condition, operates as it should. chuck is nice and tight, takes normal 8" T&G chuck jaws. Weighs about 145 lbs. $600 Located in PA.

Anyone have use for this? It's heavy. I think it's #6MT. Bearings are smooth. $250, prefer not to ship it. Located in zip 17602

$$$$ for the Newbould, $325 for the boring head.

Very good condition, full sets of all collets, ready to plug in and use. Located in PA Zip 17602 $2000

Model 2276 3 phase, 150 to 2000 RPM varispeed, VERY good condition, nice and dirty from 20 years of storage in a barn. $1600. I have a Command multi spindle head that was used on it available, also have Jacobs ball bearing chucks and tapping heads available. Located in Zip 17602, I don't have...

I occasionally use S&D HSS drills for simple jobs in manual machines. Needed a 19/32 yesterday in aluminum. I had one but it had a corner knocked off. I suck at hand sharpening, never really tried to get good at it. I generally send them out to a service because it's so cheap and they come back...

Anyone need fixture plates for your machines? Dug these out and am deciding what to do rather than put them back in the pile. Carr-Lane and AME Safeflex style, 2 pcs 26 X 24 1 pc 32 X 24. These are great plates, have 1/2 bushings and 1/2" threads on every hole on a 2" grid. I had the 2 small...

New in box, but not sure if it's the original box. $100 shipped in the US.

Vulcan strap clamps - I have 7- 4" gooseneck clamps, and 19- 4" straight clamps, of which 9 are slightly clearanced (mostly milled on one end, not butchered with a grinder). Well used, $8 each 6 5/8 T-bolts 5" long $8 each 16 T-bolts 6" long $8 each T-Bolts appear new 2 clamps with...

Very nice condition. $1600

Largish, 12 X 24" top w/3/4" T slots, 8" tall. These are the only photos I could get ATM, it's too heavy to flip over w/o help. (I can't even slide it on the plywood) I remember it being in pretty nice shape, except one corner of the top is chipped off. If you can come pick it up in zip 17602...

Kustomizer, are you out there? I have this part to make. Making 2 prototype pieces initially, I expect the production pieces to be almost the same, possibly exactly the same. I have 1 X 8 6061 plate to make them from, they are just under 1" thick to allow for a .015" skim on both sides. They...

I have a HSS 21/64 drill sticking out of a collet about 6". I plan to spin it 3000 rpm drilling a deep hole in 6061 in a VMC. Will the length to diameter ratio allow it to whip off center and break? Or just whip and drill off location? I'm spotting the hole with a 45° chamfer tool first. I...

I'm headed into some parts from 12" dia X 2.5" thick 6061. I would normally cut some soft jaws for my Chick vises to hold it by .200 or so. I'm thinking sinking a few Versa Grips in to the top of the aluminum jaws might hold better, especially considering the variable roundness of the 12" bar...

Rovi Spindle stop for 3-3/8" to 3-1/2" ID spindles. Typically found on D1-8 lathes. Good condition, hardly used but crusty from sitting, some rust on the handle. $200 plus UPS cost. Single box will be 9X9X37" and about 12 lbs from 17602, or I can ship it in a small box and a tube. Paypal is OK...

Looks unused, slightly dirty. $50 plus UPS.

In this case, 3J collets on a hydraulic closer. I've honestly never heard it discussed. The chuck on my turning center is starting to show wear on the taper where the collet taper presses on it. Grease? Oil? Just let the coolant do it?